Zebra LP 2824 Guia do Utilizador

Zebra®TMLP 2824Part #980481-001 | Rev. AUser GuideDesktop Printer

What's in the Box?Save the carton and all packing materials in case you need to ship or storethe printer later. After unpacking, make sure you h

Inspecting the PrinterLook at the outside of the printer and make sure that all parts are present.Opening the printerTo access the media compartment,

INSPECTING THE PRINTER (continued)After opening the printer, check the media compartment.4 980481-001A

Closing the printerLower the top cover.Press down until the cover snaps closed.980481-001A 5

Reporting DamageIf you discover damage or missing parts: Immediately notify and file a damage report with the shipping company.The manufacturer is not

Getting StartedThis section describes how to set up your printer for the first time and usethe most common operating procedures for loading media in t

Attaching Power SupplyCheck the power supply to make certain it is appropriate for your inputvoltage.Warning: Use the power supply that came with your

Loading Roll MediaWhen you load media, you must place the roll on the media hangers andthen adjust the media guides.You must use the correct media for

Placing the Roll in the Media CompartmentWhether your roll media is inside oroutside wound you load it into the printerthe same way.1. Open the printe

Using the GuidesThe guides direct the media toward theplaten and print head.1. Thread the media through the guides.They should just touch the edges of

ii 980481-001A

Operator ControlsPower SwitchPress backward to turn ON or forward to turn OFF the printer.CAUTION: The power should be turned off before connecting or

Media Length SensingBefore you connect the printer to your computer, make sure that the printeris in proper working order. You can do this by making

Hooking Up the Printer and ComputerYour printer will have one of these combinations of interfaces: Parallel Universal Serial Bus (USB) and DB-9 serial

USB Interface RequirementsUniversal Serial Bus (version 1.1) provides a high-speed interface that iscompatible with your existing PC hardware. USB’s

Communicating with the PrinterUniversal Serial Bus (USB) CommunicationsThe printer is a terminal device when using a universal serial bus interface.Yo

Serial CommunicationsSerial communications between the printer and the host computer can be setby theYcommand.Y CommandUse the serial port setup (Y) c

Adjusting the Print WidthPrint width must be calibrated when you use a roll with a different widthfrom previous media.Print width may be set by using

Operation & OptionsThis section helps you get the most from your printer.You must use programming to control many of the printer’s functions. Afe

Replacing SuppliesIf labels run out while printing, leave the printer power on while reloading(data loss results if you turn off the printer). After y

Printing in Peel-ModeThe optional dispenser allows youto print in “peel-mode” where thelabel backing follows a different path andthe labels are presen

Proprietary StatementThis manual contains proprietary information of Zebra Technologies Corporation. It is intended solely for the information and us

Printing on Fan-Fold MediaPrinting on fan-fold media requires you toset the media hangers in position.1. Open the top cover.2. With a sample of your m

Using the Cutter OptionPrinters that have a bezel with a motorized blade can dispense one or moreforms that are then automatically cut from the media

24 980481-001A

MaintenanceCleaningWhen you clean the printer, use one or more of the following supplies thatbest suits your needs:DESCRIPTIONCleaning pens (12)Cleani

Adhesives and coatings of media can over time transfer onto the printercomponents along the media path including the platen and print head.This build-

Platen ConsiderationsThe standard platen (drive roller) normally does not require cleaning. Paperand liner dust can accumulate without effecting print

Replacing the PlatenRemovalOpen the printer and remove any media.1. Using a pointed stylus (such astweezers, small slot-head screwdriver,or razor-knif

Replacing the Print HeadIn the event you need to replace the print head, read the procedure andreview the removal and installation steps before actual

Direct-Thermal LP ModelBefore following the steps in this procedure, open the printer bypulling the release latches forward then lifting the top cover

Replacing the LP Print Head (Continued)Assembly1. Align the print head to plug the leftand right connectors into the wirebundles.2. Slip the ground wi

Shock HazardThe printer and power supply should never be operated in a location whereeither one can get wet. Personal injury could result.MediaAlways

32 980481-001A

TroubleshootingWhat the Status Light is Telling YouColor Status Solution or ReasonNone off1. Check power connection from the A.C. outlet to powersuppl

Printer OperationProblem Solution or ReasonMedia does notadvance.1. Check interface cable connections from computer toprinter.2. Make sure top cover i

Media HandlingProblem Solution or ReasonLabel DispenserPrinting continuesbetween labels.1. Make sure label-taken sensor is on.2. The label-taken senso

Print Quality ProblemsNo print on the label. You must use the correct media for the method of printing you require.You must use direct thermal media.

The printing does not start at the top of the label, or misprinting ofone to three labels. The media may not be threaded under the media guides. Refe

Manual CalibrationManual calibration is recommended whenever you are using pre-printedmedia or if the printer will not correctly auto calibrate.1. Mak

Resetting the Factory Default ValuesSometimes, resetting the printer to the factory defaults solves some of theproblems. For troublehooting and to ov

Feed Button ModesPrinter Condition Feed Button ActionPrinter is OFFPrinter is off. Tapping or holding the button has no result.Printer is ONCover is o

AppendixInterfacesUniversal Serial Bus (USB) ConnectorThe figure below displays the cable wiring required to use the printer’sUSB interface.For inform

ContentsIntroductionHello!. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1What's in th

Parallel InterfaceThe figure below displays the cable wiring required to use the printer'sCentronics parallel interface.42 980481-001APRINTERDB-2

ZebraNet® PrintServer II™ for Ethernet NetworksThis interface uses an RJ-45 straight-through cable type. The table belowprovides the pinout assignmen

Serial (RS-232) ConnectorThe printer operates as a Data Communication Equipment (DCE) andnormally connects via a standard RS-232 modem cable to a Data

Serial (RJ-11) Alternative ConnectorThe printer operates as a Data Communication Equipment (DCE) and thoseprinters with ethernet connectors also have

46 980481-001A

Operation & OptionsThermal Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Replacing Supplies . .

980481-001A vii

980481-001A

IntroductionThis section describes what you get in your shipping box and provides anoverview of printer parts. This section also has procedures that