Zebra MP6000 Especificações Página 97
- Página / 210
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
SITE PREPARATION AND INSTALLATION 3 - 7
Remove Existing Bioptic Scanner and Accessories
If you are replacing existing equipment, follow these step to remove the old unit:
1. Ensure the POS is logged off, and the drawer was cleared by the store personnel. This varies by location.
Some IT Departments may require the POS to be completely shut down.
2. Unplug the current bioptic scanner from its power supply.
3. Prior to removing cables, make a note of the current cable runs.
4. Remove all cables connected to the bioptic scanner. Do not cut cables if you are using, or selling the old
equipment.
5. If applicable, unplug the current hand-held device from its power supply, and disconnect it from the current
bioptic scanner/host.
a. If reusing the hand-held device, leave its cable runs intact.
b. If the hand-held device was attached to the bioptic scanner with an RS-232 cable, a new cable and a
new hand-held device configuration is required.
6. If a Sensormatic connection is present, there are two cables to be aware of:
a. The large cable to the coils/antennas - disconnect from the current bioptic but leave in place.
b. The RS-232 cable to the Sensormatic controller communications port - use its run to assist replacing it.
7. If a Scale Display is present:
a. Make a note of how the current display was mounted and determine if the current placement can
accommodate the new Scale Display. Adjustments to the layout, and cable run may be required.
b. Unplug the old Scale Display power.
c. Remove it from the checkstand.
d. Remove its cables.
e. Remove the Scale Display.
8. Remove the existing bioptic scanner.
Unpacking MP6000 Equipment
To unpack equipment:
1. Remove all components from their packaging, and check that all parts are present. Each box includes the
material listed in Table 3-1. Each of the items listed is contained in separate packaging within the box and
is recognizable as a discrete item. Power cables, host to scanner communications cables, leveling screws,
and trim filler kit are all sold separately in kits.
Table 3-1
MP6000 Box Contents
Description Part Number
MP6000 w/o Platter MP6xx0-xx000M010xx
Platter 22-159817-xxx
Checkpoint Antenna 10-162248-xx
Regulatory Guide 72-171321-xx
NOTE An optional Scale Display, p/n MX201-SR00004ZZWR, is available separately for scale models only.
- INTEGRATOR GUIDE 1
- Warranty 4
- Revision History 5
- Table A 6
- TABLE OF CONTENTS 9
- Table of Contents ix 11
- Table of Contents xi 13
- ABOUT THIS GUIDE 15
- Notational Conventions 16
- Related Publications 16
- About This Guide vii 17
- FEATURES 19
- Product Overview 20
- Configurations 21
- 1 - 4 MP6000 INTEGRATOR GUIDE 22
- Table 1-1 23
- 1 - 6 MP6000 INTEGRATOR GUIDE 24
- Peripherals 26
- Features of the MP6000 27
- Left Side View 28
- View Under Platter 29
- Leveling Screws 29
- Figure 1-6 30
- Features Summary 31
- 2 - 2 MP6000 INTEGRATOR GUIDE 36
- Programming Management Tools 37
- Connecting a USB Interface 38
- USB Host Parameters 40
- * IBM Table-top USB 41
- USB Device Type (continued) 42
- Figure 2-3 47
- Table 2-3 47
- (see parameter 47
- page 2-32 47
- Connect MP6000 to RS-232 Host 48
- RS-232 Parameters 49
- RS-232 Host Parameters 50
- Table 2-7 52
- Table 2-8 53
- RS-232 Host Types 54
- *Standard RS-232 55
- RS-232 Host Types (continued) 56
- RS-232 Host -NCR Variant 64
- Parameter # 1246 66
- Third Party Scale 71
- Parameter # 1294 71
- Third Party Scale (continued) 72
- Third Party Scale LED Pin 73
- Parameter # 1295 73
- *Active High 74
- Third Party Scale Zero Pin 75
- Parameter # 1296 75
- IBM RS-485 Host Parameters 78
- *None Selected 79
- RS-232 AUX 1 87
- Scale Display Port 87
- RS-232 AUX 2 88
- Checkpoint Interlock 88
- AUX A-B (Stacked USB) 88
- Table 2-15 89
- Table 2-16 89
- INSTALLATION 91
- Site Preparation 92
- Grounding 93
- Liquid Spills and Moisture 94
- Vertical Clearance 94
- Counter Cutout 95
- Ergonomics 95
- Installing Components 96
- Unpacking MP6000 Equipment 97
- Pre-Installation Notes 98
- Required Tools 99
- Secure in Place 101
- Install the Scale Display 102
- Getting Started 104
- Installing 105
- Inserting the Scan Module 109
- Connecting the USB Cable 110
- Figure 3-25 112
- Figure 3-24 112
- Install the MP6000 /Scale 115
- Figure 3-30 116
- Figure 3-31 116
- Figure 3-32 117
- Figure 3-33 117
- Optional leveling screw kit 117
- MX301-SR00004ZZWR 117
- Figure 3-34 118
- Figure 3-35 118
- Figure 3-36 119
- Figure 3-37 119
- MX301-SR00004ZZWR or 119
- MX302-SR00004ZZWR 119
- Figure 3-38 120
- Figure 3-39 120
- 11.50 in 121
- 292.2 mm 121
- 20.0 in 121
- 506.9 mm 121
- Install Sensormatic Coils 124
- Install Checkpoint Antenna 127
- Figure 3-48 128
- Figure 3-49 128
- Installing the Mounting Frame 129
- WITH A SCALE ONLY) 131
- Scale Configurations 132
- Identifying Firmware Version 132
- Legal Scale Dampening Filter 134
- Step 4 - Calibration at LOAD 135
- 4 - 6 MP6000 INTEGRATOR GUIDE 136
- Calibration Success 137
- Calibration Failure 137
- Verification Test 138
- Table 4-5 139
- Table 4-4 139
- Audit Tallies 141
- * Kilograms 143
- Legal Scale Units (continued) 144
- Scale Display Configuration 145
- Parameter # 986 145
- Parameter # 996 147
- * Low Vibration Sensitivity 148
- Parameter # 996 (continued) 149
- Table 4-6 151
- Overview 155
- Controls and Indicators 156
- OPERATING THE SCANNER 5 - 3 157
- Volume/Tone Control Button 158
- Soft Reset Buttons 159
- Single Interval Range Scales 160
- Dual Interval Range Scales 160
- OPERATING THE SCANNER 5 - 7 161
- 5 - 8 MP6000 INTEGRATOR GUIDE 162
- Scan Windows 163
- Operating Modes 164
- Programming the MP6000 164
- USB Staging Flash Drive 165
- Flash DrivesFlash Drives 166
- Loading Cloning Files 167
- Scanning 169
- Weighing Items 170
- Supported EAS Controllers 171
- Sensormatic EAS Hard Tags 172
- OPERATING THE SCANNER 5 - 19 173
- Beeper and LED Conditions 174
- OPERATING THE SCANNER 5 - 21 175
- Table 5-1 176
- OPERATING THE SCANNER 5 - 23 177
- CHAPTER 6 123SCAN2 179
- Requirements 180
- APPENDIX A MAINTENANCE 181
- TROUBLESHOOTING, AND 181
- ERROR CODES 181
- Troubleshooting 182
- Troubleshooting Assistance 183
- A - 4 MP6000 INTEGRATOR GUIDE 184
- Table A-1 185
- Scale Warning Codes 186
- A - 8 MP6000 INTEGRATOR GUIDE 188
- Technical Specifications 189
- B - 2 MP6000 INTEGRATOR GUIDE 190
- Table B-1 191
- B - 4 MP6000 INTEGRATOR GUIDE 192
- APPENDIX C HOST INTERFACE 193
- CHARACTER SETS 193
- RS-232 Character Sets 194
- Table C-1 195
- C - 4 MP6000 INTEGRATOR GUIDE 196
- C - 6 MP6000 INTEGRATOR GUIDE 198
- Table D-1 199
- D - 2 MP6000 INTEGRATOR GUIDE 200
- APPENDIX E COMMUNICATION 201
- PROTOCOLS 201
- E - 2 MP6000 INTEGRATOR GUIDE 202
- Numerics 203
- Index - 3 205
- Tell Us What You Think 207
Diodes AP78L05/08/12 manuály
Uživatelské manuály a uživatelské příručky pro Hardware Diodes AP78L05/08/12.
Poskytujeme 1 manuály pdf Diodes AP78L05/08/12 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Diodes AP78L05/08/12 Uživatelský manuál (16 strany)
Značka: Diodes | Kategorie: Hardware | Velikost: 0.29 MB |
Tabulka s obsahem
Další produkty a příručky pro Hardware Diodes
| Modely | Typ Dokumentu |
|---|---|
| AZV331 |
Uživatelský manuál
Diodes AZV331 User Manual,
15 stránky
|
| AZV831/2 |
Uživatelský manuál
Diodes AZV831/2 User Manual [it] ,
27 stránky
|
| AS78XXA |
Uživatelský manuál
Diodes AS78XXA User Manual [it] ,
23 stránky
|
| APX803/D |
Uživatelský manuál
Diodes APX803/D User Manual [it] ,
11 stránky
|
| AZ317 |
Uživatelský manuál
Diodes AZ317 User Manual [it] ,
15 stránky
|
| APX809/810 |
Uživatelský manuál
Diodes APX809/810 User Manual [it] ,
9 stránky
|
| APX811/812 |
Uživatelský manuál
Diodes APX811/812 User Manual [it] ,
10 stránky
|
| AZ78LXX |
Uživatelský manuál
Diodes AZ78LXX User Manual [it] ,
17 stránky
|
| AS78LXX |
Uživatelský manuál
Diodes AS78LXX User Manual,
17 stránky
|
| APX823/APX824/APX825A |
Uživatelský manuál
Diodes APX823/APX824/APX825A User Manual [it] ,
12 stránky
|
| AZ809/AZ810 |
Uživatelský manuál
Diodes AZ809/AZ810 User Manual [it] ,
9 stránky
|
| AZ70XX |
Uživatelský manuál
Diodes AZ70XX User Manual,
13 stránky
|
| AP432_A |
Uživatelský manuál
Diodes AP432_A User Manual [it] ,
15 stránky
|
| AZ431L |
Uživatelský manuál
Diodes AZ431L User Manual [it] ,
18 stránky
|
| AZ432 |
Uživatelský manuál
Diodes AZ432 User Manual,
18 stránky
|
| AP431_A |
Uživatelský manuál
Diodes AP431_A User Manual,
17 stránky
|
| AN431 |
Uživatelský manuál
Diodes AN431 User Manual,
14 stránky
|
| AS431 |
Uživatelský manuál
Diodes AS431 User Manual [it] ,
19 stránky
|
| AS431I |
Uživatelský manuál
Diodes AS431I User Manual [it] ,
16 stránky
|
| AZ431A |
Uživatelský manuál
Diodes AZ431A User Manual,
21 stránky
|
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais