Zebra ZT420 Guia do Utilizador Página 76
- Página / 192
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Printer Configuration and Adjustment
Adjust Printer Settings
76
P1066582-002 ZT400 Series™ User Guide 4/8/14
Enable ZBI Zebra Basic Interpreter (ZBI 2.0™) is a programming option that may be purchased for
your printer. If you would like to purchase this option, contact your Zebra reseller for
more information.
Accepted values: N/A
Related ZPL command(s):
none
SGD command used:
zbi.key (identifies if the ZBI 2.0 option is enabled
or disabled on the printer)
User menu item: ZBI ENABLED? on page 99
Printer web page: N/A
Run a ZBI
Program
If you have ZBI installed, you may choose to run a ZBI program that you have
downloaded to your printer.
Accepted values:
N/A
Related ZPL command(s):
^JI, ~JI
SGD command used:
zbi.control.run
User menu item:
RUN ZBI PROGRAM on page 99
Printer web page: Directory Listing
Stop a ZBI
Program
If your printer is running a ZBI program, you may stop that program.
Accepted values:
N/A
Related ZPL command(s):
~JQ
SGD command used:
zbi.control.terminate
User menu item:
STOP ZBI PROGRAM on page 99
Printer web page: Directory Listing
Table 2 • Calibration and Diagnostic Tools (Continued)
- ZT400 Series™ 1
- User Guide 1
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- About This Document 9
- Who Should Use This Document 10
- Introduction 11
- Printer Options 12
- Printer Components 13
- Control Panel 14
- Zebra printer 15
- Types of Media 16
- Printer Setup and Operation 17
- Ribbon Overview 18
- Adhesive Test 19
- Ribbon Scratch Test 19
- Printer Setup and 21
- Operation 21
- Handling the Printer 22
- I) may damage the 24
- Data Cables 26
- 115 V AC 27
- 230 V AC 27
- Power Cord Specifications 28
- Select a Print Mode 30
- Rewind mode 33
- Load the Media 34
- Roll Media 35
- Fanfold Media 35
- Rear Feed 36
- Bottom Feed 36
- Roll Media (Continued) 37
- (Continued) 37
- If using… Then… 39
- Final Steps for Tear-Off Mode 40
- 4. Close the media door 41
- Rewind Option 46
- Liner Take-Up Option 46
- Final Steps for Rewind Mode 51
- Load the Media—Rewind Mode 52
- Final Steps for Cutter Mode 57
- 5. Close the media door 59
- Load the Ribbon 60
- Printer Setup 61
- If... Then 63
- PAUSE to enable printing 63
- Printer Configuration 65
- Adjust Printer Settings 66
- Print Settings 67
- • THERMAL TRANS 68
- • DIRECT THERMAL 68
- • TEAR OFF 69
- • CUTTER 69
- FEED + CANCEL during printer 71
- ~JD to enable, ~JE to disable 75
- ^JI, ~JI 76
- Network Settings 77
- RFID Settings 80
- RFID ANTENNA 81
- Language Settings 83
- • ZPL II 85
- Sensor Settings 86
- Port Settings 87
- • XON/XOFF 88
- • RTS/CTS 88
- • DSR/DTR 88
- BlueTooth Settings 89
- User Menus 90
- HOME MENU 91
- SETTINGS 91
- ▼ XXXXXXX ▲ 93
- SETTINGS Menu 94
- LEFTARROW 95
- TOOLS Menu 97
- NONE is listed 99
- RIGHT SELECT to select STOP 99
- User Menus—TOOLS Menu 100
- Network Menu Shortcut 101
- or RIGHT ARROW 101
- NETWORK Menu 102
- User Menus—NETWORK Menu 103
- RFID Menu Shortcut 107
- RFID Menu 108
- User Menus—RFID Menu 109
- OK or press 110
- RIGHT SELECT to select GO 110
- LEFTARROW or RIGHT ARROW 110
- LANGUAGE Menu 111
- SENSORS Menu 113
- TAKE LABEL 114
- PORTS MENU 114
- PORTS Menu 115
- ZEBRA TECHNOLOGIES 116
- WML S1.09 © 116
- BLUETOOTH MENU 116
- BLUETOOTH Menu 117
- LOAD BACKING 119
- REMOVE RIBBON 119
- CALIBRATING 121
- PLEASE WAIT 121
- RELOAD ALL 122
- CONTINUE 122
- Reload the ribbon (if used) 123
- Close the printhead 123
- Close the media door 123
- Adjust the Printhead Pressure 124
- If the media... Then 125
- Remove Used Ribbon 128
- Routine Maintenance 129
- Area Method Interval 130
- Printer Exterior 131
- Media Compartment and Sensors 131
- Raise the media door 132
- 8. Close the media door 135
- Clean the Peel Assembly 136
- Clean the Cutter Module 140
- Remove the cutter shield 141
- Replacing Printer Components 144
- Lubrication 144
- Troubleshooting 145
- Meaning of Indicator Lights 146
- Printing Issues 148
- Ribbon Problems 151
- RFID Problems 152
- MEDIA POWER UP and 153
- O) and then back on (I) too 154
- O) the printer 154
- I) the printer 154
- Error Messages 155
- RIBBON OUT 156
- PH NOT AUTHENTICATED 156
- REPLACE PRINTHEAD 156
- Display/ 158
- Indicator Lights 158
- Communications Problems 159
- Miscellaneous Issues 160
- Printer Diagnostics 162
- CANCEL Self Test 163
- PAUSE Self Test 164
- FEED Self Test 165
- Print Quality Description 166
- FEED + PAUSE Self Test 168
- CANCEL + PAUSE Self Test 168
- FE indicates a framing error 169
- PE indicates a parity error 169
- NE indicates noise 169
- Sensor Profile 170
- Specifications 173
- General Specifications 174
- Printing Specifications 175
- Media Specifications 176
- Ribbon Specifications 177
- Glossary 179
- 4/8/14 P1066582-002 183
Manuais e produtos relacionados com Impressoras de rótulos Zebra ZT420
Impressoras de rótulos Zebra GC420t Guia do Utilizador
(116 páginas)
(116 páginas)
Impressoras de rótulos Zebra ZM400 Guia do Utilizador
(116 páginas)
(116 páginas)
Impressoras de rótulos Zebra ZD500 Guia do Utilizador
(160 páginas)
(160 páginas)
Impressoras de rótulos Zebra GC420d Guia do Utilizador
(100 páginas)
(100 páginas)
Impressoras de rótulos Zebra GX430D Guia do Utilizador
(128 páginas)
(128 páginas)
Impressoras de rótulos Zebra T5206R Manual do Utilizador
(394 páginas)
(394 páginas)
Impressoras de rótulos Zebra Z6Mplus Guia do Utilizador
(166 páginas)
(166 páginas)
Diodes AP78L05/08/12 manuály
Uživatelské manuály a uživatelské příručky pro Hardware Diodes AP78L05/08/12.
Poskytujeme 1 manuály pdf Diodes AP78L05/08/12 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentários a estes Manuais