Zebra 105SL Plus Guia do Utilizador Página 59
- Página / 174
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
51
Operations
Load Media in Rewind Mode
6/30/06 105SL User Guide 11342L-001 Rev. A
4. Open the printhead assembly by rotating the printhead-open lever counterclockwise.
5. Loosen the thumb screw on the bottom of the outer media guide (not visible from this
angle).
6. Slide the outer media guide all the way out.
- User Guide 1
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- Who Should Use This Document 10
- Contacts 11
- Document Conventions 12
- SETUP/EXIT button 13
- About This Document 14
- Introduction 15
- External View 16
- Control Panel 17
- Control Panel LCD 18
- Control Panel Buttons 18
- Control Panel Lights 19
- Printer Media Compartment 21
- Printer Setup 23
- Before You Begin 24
- Handling the Printer 25
- Select a Site for the Printer 26
- Connector Locations 27
- Types of Connections 28
- Data Cable Requirements 30
- 4. Turn on (I) the printer 31
- Power Cord Specifications 32
- Types of Media 33
- Ribbon Overview 35
- Adhesive Test 36
- Ribbon Scratch Test 36
- Operations 37
- Media Loading Overview 38
- Insert Media into the Printer 39
- Fanfold Media 40
- If… Then… 41
- Load Media in Tear-Off Mode 42
- Load Media in Peel-Off Mode 46
- If the printer has 47
- 1). Insert the long end 51
- If... Then 55
- Pull out the spindle hook 56
- Load Media in Rewind Mode 57
- 1) and the adjustable hook 58
- 2) point down 58
- Load Media in Cutter Mode 65
- Load Ribbon 69
- Remove Used Ribbon 73
- Adjust Media Sensors 74
- Lower Media Sensor 75
- Adjust Printhead Balance 76
- Printhead Pressure Adjustment 78
- Calibrate the Printer 79
- Setup Mode 82
- Exit Setup Mode 83
- Default Password Value 84
- Print a Configuration Label 85
- LIST NETWORK 86
- TEAR OFF +000 88
- - + 88
- PRINT MODE 88
- -TEAR-OFF + 88
- Action/Explanation 89
- PRINT WIDTH 90
- - MM + 90
- MAXIMUM LENGTH 91
- -39.0 IN 988 MM 91
- To format a memory card: 93
- To initialize Flash memory: 94
- SENSOR PROFILE 95
- PRINT 95
- To change the value shown: 100
- Parameter 100
- LEFT POSITION 102
- - ±0000 + 102
- HEAD RESISTOR 103
- - 0500 OHMS + 103
- To skip these parameters: 104
- Print Server LCD Displays 106
- ^WE ZPL command to set 108
- PLUS (+) to select YES 109
- Parameter Action/Explanation 109
- Configuration 110
- Control Panel Parameters 110
- PC and Memory Cards 111
- PCMCIA PC Cards 112
- PAUSE light flashes 113
- PAUSE light flashes only 113
- Routine Maintenance 115
- Lubrication 116
- Cleaning Schedule 116
- Clean the Exterior 117
- Take-label sensors 121
- Black mark sensor 121
- Ribbon sensor 121
- Clean the Snap Plate 122
- Clean the Cutter 123
- Replace the Fuse 124
- Troubleshooting 125
- Troubleshooting Checklists 126
- LCD Error Messages 127
- LCD Display/ 128
- Printer Condition 128
- HEAD COLD 129
- OUT OF MEMORY 129
- (function) 129
- Print Quality Problems 130
- Note • A vertical drift of 132
- Calibration Problems 133
- Communications Problems 134
- Ribbon Problems 135
- LANGUAGE 136
- SAVE CHANGES in the 136
- Calibrate 137
- Printer Diagnostics 138
- CANCEL Self Test 139
- PAUSE Self Test 141
- FEED Self Test 142
- Print Quality Description 144
- FEED and PAUSE Self Test 146
- Sensor Profile 148
- Specifications 149
- General Specifications 150
- Communications Specifications 151
- Other Standard Features 151
- Additional Options 151
- Agency Approvals 152
- Printing Specifications 153
- Ribbon Specifications 153
- Media Specifications 154
- Bar Codes 155
- Glossary 157
- End User License 161
- Agreement 161
- End User License Agreement 162
- HEAD COLD message, 121 168
- HEAD TOO HOT message, 120 168
- OUT OF MEMORY message, 121 169
- PAPER OUT message, 120 170
- RIBBON IN message, 120 171
- RIBBON OUT message, 119 171
- © 2006 ZIH Corp 174
Manuais e produtos relacionados com Digitalizar e Imprimir Zebra 105SL Plus
Digitalizar e Imprimir Zebra TTP2130 Especificações
(138 páginas)
(138 páginas)
Digitalizar e Imprimir Zebra 2443 Manual de Serviço
(76 páginas)
(76 páginas)
Digitalizar e Imprimir Zebra 10/100 Guia do Utilizador
(106 páginas)
(106 páginas)
Digitalizar e Imprimir Zebra ZE500 Guia do Utilizador
(170 páginas)
(170 páginas)
Digitalizar e Imprimir Zebra GX420t Guia do Utilizador
(108 páginas)
(108 páginas)
Digitalizar e Imprimir Zebra EPL2 Especificações
(138 páginas)
(138 páginas)
Digitalizar e Imprimir Zebra KR203 Especificações
(36 páginas)
(36 páginas)
(76 páginas)
(64 páginas)
Digitalizar e Imprimir Zebra 170PAX4 Guia do Utilizador
(164 páginas)
(164 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais