Zebra 105SL Plus Guia do Utilizador Página 154
- Página / 180
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Troubleshooting
Printer Diagnostics
154
P1056468-002 7/3/13
FEED + PAUSE Self Test
Performing this self test temporarily resets the printer configuration to the factory default
values. These values are active only until power is turned off unless you save them
permanently in memory. If the factory default values are permanently saved, a sensor
calibration procedure must be performed. (See Calibrate the Ribbon and Media Sensors
Manually on page 106.)
To perform a FEED and PAUSE self test, complete these steps:
1. Turn off (O) the printer.
2. Press and hold FEED + PAUSE while turning on (I) the printer.
3. Hold FEED + PAUSE until the first control panel light turns off.
The printer configuration is reset to the factory default values. No labels print at the end of
this test.
CANCEL + PAUSE Self Test
Performing this self test temporarily resets the network configuration to the factory default
values. These values are active only until power is turned off unless you save them
permanently in memory.
To perform a CANCEL and PAUSE self test, complete these steps:
1. Turn off (O) the printer.
2. Press and hold CANCEL + PAUSE while turning on (I) the printer.
3. Hold CANCEL + PAUSE until the first control panel light turns off.
The printer’s network configuration is reset to the factory default values. No labels print at
the end of this test.
- 105SLPlus™ 1
- User Guide 1
- Part Number: P1056468-002 2
- Declaration of Conformity 3
- Compliance Information 4
- Contents 5
- Who Should Use This Document 10
- Document Conventions 11
- About This Document 12
- Introduction 13
- Printer Components 14
- Control Panel 15
- Control Panel Display 17
- Perform an action 18
- Change Parameter Values 18
- Default Password Value 20
- WARNING CLEAN PRINTHEAD 23
- YES to reset 23
- WARNING REPLACE HEAD 24
- 3. Do you want to continue? 26
- PERMANENT 33
- Printer Setup and 37
- Operation 37
- Handling the Printer 38
- Printer Setup and Operation 39
- I) may damage the 40
- Data Cables 42
- 115 V AC 43
- 230 V AC 43
- Power Cord Specifications 44
- Printer Setup 46
- Types of Media 47
- Ribbon Overview 49
- Adhesive Test 50
- Ribbon Scratch Test 50
- Select a Print Mode 51
- Load the Ribbon 54
- If… Then… 55
- 2) until it locks into place 58
- Load the Media 59
- 1) all the way out 60
- Bottom Feed 61
- Rear Feed 61
- RIBBON OUT error 62
- 1), under the 63
- Rewind Mode on page 72 64
- Mode on page 77 64
- 11. Close the media door 66
- Printer Configuration 81
- Print Settings 83
- ~JS when received 87
- • the non-resettable counter 90
- Important • 94
- Directory Listing 95
- Network Settings 96
- Print Server Settings > 99
- Factory Print Server Settings 99
- Language Settings 100
- • ZPL II 101
- Sensor Settings 102
- Port Settings 103
- Changing Printer Settings 104
- DSR/DTR for host handshake 105
- ZEBRA response messages are 105
- LOAD BACKING 106
- Raise the media door 107
- If you are using… Then… 108
- REMOVE RIBBON 109
- CALIBRATING 110
- PLEASE WAIT 110
- RELOAD ALL 110
- Close the media door 111
- Remove Used Ribbon 112
- If... Then 113
- Pull out the spindle hook 114
- Upper Media Sensor 115
- Routine Maintenance 116
- Lower Media Sensor 118
- Toggle Position Adjustment 119
- I) the printer.) 120
- Printhead Pressure Adjustment 121
- Replacing Printer Components 124
- Lubrication 124
- CLEAN HEAD NOW appears 125
- Clean the Sensors 128
- Transmissive Media Sensor 129
- Clean the Snap Plate 130
- Clean the Cutter 134
- Troubleshooting 135
- Printing Issues 136
- Error Messages 139
- 1) is likely 140
- O) the printer 141
- I) the printer 141
- Display/ 143
- Printer Condition 143
- Calibration Problems 144
- Communications Problems 145
- Ribbon Problems 146
- Miscellaneous Issues 147
- Printer Diagnostics 148
- CANCEL Self Test 149
- PAUSE Self Test 150
- FEED Self Test 151
- Print Quality Description 152
- FEED + PAUSE Self Test 154
- CANCEL + PAUSE Self Test 154
- FE indicates a framing error 155
- PE indicates a parity error 155
- NE indicates noise 155
- Sensor Profile 156
- MEDIA (3) for the media 157
- Specifications 159
- Features 160
- Bar Codes 161
- General Specifications 162
- Print Specifications 163
- Media Specifications 164
- Ribbon Specifications 165
- Glossary 167
- 7/3/13 P1056468-002 171
- P1056468-002 7/3/13 172
- 7/3/13 P1056468-002 173
Manuais e produtos relacionados com Digitalizar e Imprimir Zebra 105SL Plus
Digitalizar e Imprimir Zebra EM 220 Especificações
(67 páginas)
(67 páginas)
Digitalizar e Imprimir Zebra 105Se Especificações
(110 páginas)
(110 páginas)
Digitalizar e Imprimir Zebra CPCL Especificações
(70 páginas)
(70 páginas)
Digitalizar e Imprimir Zebra TTPM2 Especificações
(140 páginas)
(140 páginas)
(86 páginas)
Digitalizar e Imprimir Zebra CPCL Especificações
(497 páginas)
(497 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais