Zebra 170PAX4 Guia do Utilizador Página 102
- Página / 164
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Routine Maintenance
Power Fuse Replacement
94
57516L-002 Rev. A 170PAX4 User Guide 1/10/06
Notes • ___________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
__________________________________________________________________________
- User Guide 1
- DECLARATION OF INCORPORATION 3
- Compliance Information 4
- Contents 5
- Who Should Use This Document 10
- Contacts 11
- Document Conventions 12
- About This Document 13
- Introduction 15
- Print Engine Exterior View 16
- Control Panel 17
- Description/Function 18
- Power On/Off Switch 20
- Print Engine Setup 21
- Before You Begin 22
- Handling the Print Engine 23
- Print Engine Installation 24
- Mounting screws (four total) 28
- Applicator 28
- Power Cord Specifications 30
- Connector Locations 31
- Types of Connections 32
- Data Cable Requirements 34
- Types of Media 35
- Ribbon Overview 37
- Adhesive Test 38
- Ribbon Scratch Test 38
- Operations 39
- Load Media 40
- Figure 21 • Loaded Media 41
- 2. Open the media door 42
- 16. Close the media door 46
- Load Ribbon 47
- Figure 24 • Loaded Ribbon 48
- 9. Close the media door 51
- Remove Used Ribbon 52
- Calibrate the Print Engine 53
- Ribbon Sensor 55
- Reflective Media Sensor 55
- Transmissive Media Sensor 55
- If the media... Then 56
- Configuration 57
- Setup Mode 58
- Exit Setup Mode 59
- Default Password Value 60
- Print a Configuration Label 61
- LIST NETWORK 62
- Control Panel LCD Displays 63
- 6 IPS + 64
- BACKFEED SPEED 64
- 2 IPS + 64
- SLEW SPEED 64
- TEAR OFF +000 65
- - + 65
- PRINT MODE 65
- -APPLICATOR + 65
- Action/Explanation 66
- MAXIMUM LENGTH 67
- -39.0 IN 988 MM 67
- To change the value shown: 68
- Parameter 68
- To reset the media counter: 69
- To reset the ribbon counter: 69
- To format a memory card: 73
- To initialize Flash memory: 74
- SENSOR PROFILE 75
- PRINT 75
- COMMUNICATIONS 79
- - NORMAL MODE + 79
- CONTROL PREFIX 79
- - < >7EH + 79
- PERMANENT save option 81
- RIBBON TENSION 81
- - HIGH + 81
- MEDIA POWER UP 81
- - CALIBRATION + 81
- LEFT POSITION 83
- - ±0000 + 83
- HEAD RESISTOR 83
- - 0500 OHMS + 83
- APPLICATOR PORT 84
- - OFF + 84
- ERROR ON PAUSE 84
- - ENABLED + 84
- ^SP command 86
- To skip these parameters: 87
- Print Server LCD Displays 89
- ^WE ZPL command to set 91
- Parameter Action/Explanation 92
- Lubrication 94
- Cleaning Schedule 94
- Clean the Exterior 94
- Clean the Media Compartment 95
- Clean the Sensors 95
- Door-open sensor 96
- Toggle Positioning 99
- Printhead Pressure Adjustment 100
- Power Fuse Replacement 101
- Routine Maintenance 102
- Troubleshooting 103
- Troubleshooting Checklists 104
- LCD Error Messages 105
- OUT OF MEMORY 107
- (function) 107
- HEAD COLD 107
- Memory Errors 108
- Print Quality Problems 109
- Note • A vertical drift of 111
- Communications Problems 113
- LANGUAGE 114
- SAVE CHANGES in the 114
- Calibrate 115
- Print Engine Diagnostics 116
- CANCEL Self Test 117
- PAUSE Self Test 118
- FEED Self Test 119
- Print Quality Description 121
- FEED and PAUSE Self Test 123
- Parameter Controlled By 124
- Data Ports 127
- Parallel Data Port 128
- 36-Pin Connectors 129
- Serial Data Port 130
- Pin Configuration 131
- RS-232 Interface Connections 132
- Modem Connection 133
- Applicator Signals 134
- Isolated (External Power) 140
- Non-Isolated (Internal Print 140
- Engine Power) 140
- Fuse and Jumper Locations 141
- Specifications 143
- General Specifications 144
- Other Standard Features 145
- Additional Options 145
- Agency Approvals 146
- Media Specifications 147
- Ribbon Specifications 148
- Printing Specifications 149
- Bar Codes 150
- Glossary 151
- HEAD TOO HOT 156
- PAPER OUT 158
- RIBBON IN 159
- RIBBON OUT 159
- © 2006 ZIH Corp 164
Manuais e produtos relacionados com Digitalizar e Imprimir Zebra 170PAX4
Digitalizar e Imprimir Zebra Z6Mplus Guia do Utilizador
(142 páginas)
(142 páginas)
(27 páginas)
Digitalizar e Imprimir Zebra 110PAX4 Guia do Utilizador
(164 páginas)
(164 páginas)
Digitalizar e Imprimir Zebra TTPM3 Especificações
(112 páginas)
(112 páginas)
Digitalizar e Imprimir Zebra EM 220 Especificações
(67 páginas)
(67 páginas)
Digitalizar e Imprimir Zebra 105Se Especificações
(110 páginas)
(110 páginas)
Digitalizar e Imprimir Zebra CPCL Especificações
(70 páginas)
(70 páginas)
Digitalizar e Imprimir Zebra TTPM2 Especificações
(140 páginas)
(140 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.176 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais