Zebra TTP2130 Especificações Página 106
- Página / 138
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Page Setup
Parameters Used
106
P1003640-001 TTP2100 Technical Manual 10/22/2008
FF (Form Feed)
Use FF to print the buffer content, go to the next top of form (black-mark), and cut the paper.
ESC Z (Go To Next Top of Form)
Use ESC Z to move the paper to the next top of form. This is practically a Form-Feed without
printing and cut. It searches for the next black-mark for maximum one page length + black-
mark length (256 x n37+n38 + n39)/8. An additional length of 20mm is added to be sure to
pass the edge of the next black-mark. If there is no black-mark within the set distance plus
20 mm, an error is raised.
The commands are used together in the following way:
Example • The following examples are not made for a specific programming language or
editor, but can be implemented with the tools of your choice. The data sent to the printer are
marked with “Send→”.
When setting up the printer:
Send→ ESC & P 35d 1d Enables black-mark sync
Send→
ESC & P 37d 4d Sets distance between two black-marks
Send→
ESC & P 38d 0d n37=4d and n38=0d gives 128 mm
Send→
ESC & P 39d 80d Sets max Black-mark to 80 x 0.125 = 10mm
Send→
ESC & P 40d 24d Sets max Black-mark to 24 x 0.125 = 3 mm
Send→
ESC & P 41d 0d
Send→ ESC & P 42d 200d Sets Black-mark offset to 200 x 0.125 = 25mm
Send→
ESC & P 43d 0d
Send→ ESC & P 44d 0d Sets Black-mark top margin to 0mm
Send→
ESC & 4d Stores the above parameters as default parameters.
The above set up and stores the parameters in the EEPROM of the printer, so this needs only
be sent once to the printer when setting it up for Black-mark sync.
Document:
Send→ the text and graphics
At the end of the document:
Send→ ESC Z Feeds the printout to the next black-mark + the additional feed specified by
the ESC x command.
Send→ RS Cuts and ejects the printout.
- Zebra® TTP2100 1
- Technical Manual 1
- Contents 3
- Introduction 7
- Contacts 8
- Product Presentation 10
- Print and drop 11
- Print and take 11
- Controls 12
- Description 13
- Installation 15
- Installing a Paper Guide 16
- 11. Press SET 17
- 12. Press STORE 17
- Value When Used 17
- 3. Tighten the screw 18
- Calibrating the TOF Sensor 19
- Installation Considerations 20
- Quick-Fit Hubs 21
- Push down 22
- Ambient Light 24
- Paper low 25
- Connector 25
- Connecting to the Computer 26
- TTP 2130 27
- Connecting the Power 29
- Oscilloscope Setting 2A/div 30
- Self-test 31
- Making a Test Printout 32
- Installing a Printer Driver 33
- Printer Features 35
- Black-mark Settings: 36
- Operation 37
- Loading Fanfold Ticket Stock 38
- Temperature-sensitive 39
- SW96074C 39
- Wrong! Wrong! Wrong! 40
- 1. Open the printer lid 41
- Clearing Paper Jams 42
- Programming 43
- Driver Oriented 44
- ESC ! n1 45
- Select font 45
- 1B 23 Hex 48
- 27 35 decimal 48
- 1B 5A Hex 48
- 27 90 Decimal 48
- Software command syntax 49
- Barcode Commands 53
- Name Dec Hex 55
- 1B 42 57 n1 nx Hex 56
- 027 066 087 n1 nx Decimal 56
- 1B 42 43 n1 hex 56
- 27 66 67 n1 decimal 56
- 1B 7C n1 nx Hex 57
- 027 124 n1 nx Decimal 57
- 1B 62 n1...n5 Data hex 58
- 27 98 n1...n5 Data decimal 58
- 1B 73 nDataHex 58
- 27 115 n Data Decimal 58
- 1B 72 n1...n9 hex 59
- 27 114 n1...n9 decimal 59
- 1B 67 n1...n5 hex 60
- 27 103 n1...n5 decimal 60
- 1B 4C n1 Hex 60
- 27 76 n1 Decimal 60
- Print Commands 61
- Cut and Present Commands 62
- System Related Commands 64
- 1B 26 73 0A hex 67
- 27 38115 10 decimal 67
- 1B 00 Hex 67
- 27 0 Decimal 67
- Status Code Meaning 68
- 1B 05 04 hex 70
- 27 5 4 decimal 70
- 1B 05 05 hex 70
- 27 5 5 decimal 70
- 1B 05 06 hex 71
- 27 5 6 decimal 71
- 2. The printer is printing 72
- 1B 05 0C hex 74
- 27 5 12 decimal 74
- 1B 05 63 hex 74
- 27 5 99 decimal 74
- 1B 05 45 hex 75
- 27 5 69 decimal 75
- 1B 05 50 n1 Hex 76
- 27 5 80 n1 Decimal 76
- 1B 06 n1 hex 76
- 27 6 n1 decimal 76
- Font Loading 77
- Character Bitmap Data 78
- Logotypes 79
- Printing 80
- Status Reporting 81
- Default Parameter Settings 83
- Default Value 84
- Examples 84
- Summary of Parameter Settings 85
- TTP model 86
- 2110 2130 86
- Serial Interface Set-up 87
- Print Setup 88
- Fixed Document Mode 91
- Cut Position Calibration 93
- Wall Compensation (mm) 93
- TOF Sensor Mask 97
- BM Sensor 97
- Printable Area 100
- Page Setup 101
- Simple Calibration Process 102
- Parameters Used 103
- FF (Form Feed) 106
- Interface 109
- Parameter Options 110
- USB, TTP 2130 111
- Maintenance 113
- Symptom Suggested actions 114
- 1. Open the printhead 115
- Firmware 116
- FW version Change 117
- Maintenance 118
- Specifications 119
- Ticket Specifications 120
- TOF Detection 120
- Print Module 121
- Ticket Separation 121
- Presenter 121
- Electronics 122
- Text Mode 122
- Basic Character Set 123
- Miscellaneous 124
- Ordering Number List 124
- Printer Shown on 125
- Dimensions 126
- Media Holder 127
- 70W Power Supply 128
- 150W Power Supply 129
- Part Number: P1003640-001 138
- © 2008 ZIH Corp 138
Manuais e produtos relacionados com Digitalizar e Imprimir Zebra TTP2130
Digitalizar e Imprimir Zebra 2443 Manual de Serviço
(76 páginas)
(76 páginas)
Digitalizar e Imprimir Zebra 10/100 Guia do Utilizador
(106 páginas)
(106 páginas)
Digitalizar e Imprimir Zebra ZE500 Guia do Utilizador
(170 páginas)
(170 páginas)
Digitalizar e Imprimir Zebra GX420t Guia do Utilizador
(108 páginas)
(108 páginas)
Digitalizar e Imprimir Zebra EPL2 Especificações
(138 páginas)
(138 páginas)
Digitalizar e Imprimir Zebra KR203 Especificações
(36 páginas)
(36 páginas)
(76 páginas)
(64 páginas)
Digitalizar e Imprimir Zebra 170PAX4 Guia do Utilizador
(164 páginas)
(164 páginas)
Digitalizar e Imprimir Zebra Z6Mplus Guia do Utilizador
(142 páginas)
(142 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais