Zebra Encore 3N Manual do Utilizador

User's ManualPortable PrinterPart No. UMAN-EN3 Rev. R March, 2003

O-4UMAN-EN3Media Type• Paper Labels• Synthetic Labels• Plain paper•Tags•Two-part thermal receipts• Linerless labels (on linerless models only)Media Ha

O-5UMAN-EN3• Power On/Off from terminal or built-in keypad• Black bar/gap sensingFormats• 25 Resident fonts• Standard international character sets• Fl

O-6UMAN-EN3CONTROLSKeypad FunctionsFeed Switch:Advances media tonext label or sensemark without printing.On switch:momentary on actionturns printer on

O-7UMAN-EN3Battery ConditioningIMPORTANT: Encore 3 batteries must be cycled severaltimes before maximum capacity is realized. A battery is cycled by

O-8UMAN-EN3ChargersListed below are the specifications for the Encore 3chargers:UCN72-4: (p/n series AC15482-tab)(Part numbers will vary depending on

O-9UMAN-EN3Battery Safety WarningsBattery terminals are recessed to prevent accidentalshort circuiting of the battery. Allowing these terminals tocon

O-10UMAN-EN3Fig. 4 Media Installation: Peeler in usePlatenEdge Guide“Open” ButtonLabelPeeler BarLinerSpindlePeelerAssembly

O-11UMAN-EN3The Encore 3 can be specified to print and separatelabels automatically using a built in label peeler. Thefollowing details media installa

O-12UMAN-EN3Fig. 5 Media Installation: Peeler not in usePlatenEdge Guide“Open” ButtonMediaSpindle

O-13UMAN-EN3INSTALLATION OF MEDIA WITHOUT PEELERThe Encore 3 can print on conventional journal stock orprint continuous batches of labels without us

iiProprietary StatementThis manual contains proprietary information of Zebra Technologies Corporation. It isintended solely for the information and u

O-14UMAN-EN3TROUBLESHOOTINGSelf Test: Perform the self test as described in theControls section. Unit should print a line of interlocking“x” charact

O-15UMAN-EN3No print (continued) c) Check cable to terminald) Invalid label format orcommand structure — useHex Dump Mode fortroubleshooting.Reduced b

O-16UMAN-EN3Communication Error: a) Check media is loaded,head is closed and errorlight is off.b) Check baud rate.c) Replace cable to terminal.Label J

O-17UMAN-EN3MAINTENANCEThe Encore 3 will provide reliable service provided afew simple guidelines are followed. The printer should becleaned periodic

O-18UMAN-EN3Cleaning the platenRefer to Figure 6Applies to printers configured for linered media only• Open the printer by pressing the “Open” button

O-19UMAN-EN3Cleaning the peeler roller:Refer to Figure 6 on pg. O-19. Applies only to units with label peeler option• Saturate a cotton swab with al

O-20UMAN-EN3COMMUNICATING TO THE PRINTERThe printer must establish communications with a hostterminal which sends the data to be printed. Communi-cat

O-21UMAN-EN3• By means of a wireless LAN (Local Area Network)(Encore 3 Network Printers only)Cable CommunicationsAll Encore 3 printers can communicate

O-22UMAN-EN3Bluetooth™ Networking Overview“Bluetooth” is a worldwide standard for the exchange ofdata between two devices via radio frequencies. Blue

O-23UMAN-EN3A Typical Bluetooth Connection SequenceIn this simplified sequence “Joe’s Terminal” is aBluetooth ready hand held terminal running an appl

iiicontinued on next pageCONTENTSIntroduction ... O-1Printer Specifications ...

O-24UMAN-EN3Wireless Local Area Network (LAN)Printers equipped for wireless Local Area Network(LAN) communications are known as Encore 3 N Net-work Pr

Appendices

A-1APPENDIX AINTERFACE CABLESPin 1Pin 9DB-9 PinFemale Plug(to P.C.)8 PinMale Plug(to printer)(TXD)(RXD)(RTS)(CTS)(GND)(DTR)(DSR)Shield(RXD)(TXD)(CTS)

A-2APPENDIX AINTERFACE CABLESCable Cord Terminal PrinterTerminal Part Number Lgth/Type Connector Connector NotesCOMPSEEApex II BL12093-3 8’ Coiled RJ

APPENDIX AINTERFACE CABLES (continued)A-3Cable Cord Terminal PrinterTerminal Part Number Lgth/Type Connector Connector NotesSYMBOL (CONT.)LRT/LDT3800

A-4APPENDIX BMEDIA SUPPLIESTo insure maximum printer life and consistent print qualityand performance for your individual application, it isrecommend

A-5APPENDIX CMAINTENANCE SUPPLIESIn addition to using quality media provided by Zebra, it isrecommended that the print head be cleaned as pre-scribed

A-6PRODUCT SUPPORTContact the Help Desk at:Zebra Technologies Corporation30 Plan WayWarwick, Rhode Island 02886-1012 USATelephone: +1 401.739.5800Fax

A-7D275,286D347,021D389,178D430,199D433,7023,964,6734,019,6764,044,9464,360,7984,369,3614,387,2974,460,1204,496,8314,593,1864,607,1564,673,8054,736,09

ivAPPENDIX AInterface Cables...A-1APPENDIX BMedia Supplies ...

Visit our Web site atwww.zebra.com

Operation Section

FIG. 1A ENCORE 3 PRINTERCableCommunicationsPortIR WindowBattery LatchKeypadHead Latch/Peeler Assy.FIG. 1 ENCORE 3N PRINTERCableCommunicationsPortIR Wi

O-1UMAN-EN3INTRODUCTIONThe Encore™ 3 Portable Printer utilizes the latest indirect thermal printing technology. This product is de-signed for portabl

O-2UMAN-EN3PRINTER SPECIFICATIONSPhysicalEncore 3 Encore 3NHeight: 5.6" (142 mm) 6.8” (173 mm)Width: 5.0" (127 mm) 5.0" (127 mm)Depth:

O-3UMAN-EN3Communications ProtocolThe Encore 3 supports RTS/CTS (hardware) and XON/XOFF handshaking protocols to synchronize with thehost terminal. T