Zebra RZ400 Guia do Utilizador descarregar pdf (Página 132)

Troubleshooting

Printer Diagnostics

132

79695L-002 Rev. A Z Series

/RZ™ Series User Guide 6/6/08

CANCEL Self Test

The CANCEL self test prints a configuration label (Figure 19).

To perform the CANCEL Self Test, complete these steps:

1. Turn off (O) the printer.

2. Press and hold CANCEL while turning on (I) the printer. Hold CANCEL until the first

control panel light turns off.

A printer configuration label prints (Figure 19).

Figure 19 • Sample Configuration Label

Z Series RZ Series

1 2 ... 127 128 129 130 131 132 133 134 135 136 137 ... 155 156

Z Series 1
/RZ™ Series 1
User Guide 1
Declaration of Conformity 3
Compliance Information 4
Contents 5
Section Description 10
Contacts 11
Document Conventions 12
FEED button 13
CANCEL button 13
About This Document 14
Introduction 15
External View 16
Printer Media Compartment 18
Control Panel 19
Control Panel Buttons 20
Control Panel Lights 21
Printer Language Modes 22
Printer Setup 23
Before You Begin 24
Temperature Relative Humidity 25
Select a Site for the Printer 26
Interface 27
Standard or 27
Optional on 27
Characteristics 27
) may damage the 28
O) position 31
Power Cord Specifications 32
Types of Media 33
Ribbon Overview 35
If the ribbon... Then 36
Operations 37
Print Mode Printer Option 39
Load Media 41
Roll Media 42
Fanfold Media 42
Roll Media (Continued) 43
Fanfold Media (Continued) 43
PAUSE to enable printing 44
Close the printhead assembly 54
Ribbon Coated Outside 55
(black ribbon spindle) 55
Ribbon Coated Inside 55
(gray ribbon spindle) 55
Load Ribbon 56
Remove Used Ribbon 59
Calibrate the Printer 60
Adjust Printhead Pressure 61
Media Width 62
If the media... Then 62
Configuration 63
Setup Mode 64
Exit Setup Mode 65
Default Password Value 66
Print a Configuration Label 67
LIST NETWORK 68
Language/Parameter 69
To change the value shown: 69
Action/Explanation 70
WARNING REPLACE 77
To print this label: 79
To initialize Flash memory: 82
To print a sensor profile: 82
LOAD BACKING prompt displays 83
RELOAD ALL displays 83
IDLE DISPLAY 93
RFID Control Panel Parameters 96
To calibrate an RFID tag: 97
RFID WRITE PWR 98
RFID ERR STATUS 98
RFID TAG TYPE 98
1122334455667788 for 2 99
RFID TAG DATA 99
RFID Operation 100
Routine Maintenance 101
Replacing Printer Components 102
Lubrication 102
Area Method Interval 103
Cleaning Procedures 104
Clean the Cutter Module 108
I) the printer 109
Troubleshooting 113
Troubleshooting Checklists 114
LCD Error Messages 115
O) the printer 116
HEAD COLD 117
HEAD TOO HOT 117
DEFRAGMENTING 118
ERROR CONDITION 118
CUTTER JAM 118
OUT OF MEMORY 118
(function) 118
Print Quality Problems 119
Note • A vertical drift of 121
Calibration Problems 122
NONE. See 123
Ribbon Problems 124
RFID TAG 125
MEDIA POWER UP and 126
RFID Problems 127
LANGUAGE 128
SAVE CHANGES in the 128
O) and then on (I) 129
CANCEL self tests 131
CANCEL Self Test 132
PAUSE Self Test 133
FEED Self Test 134
Printer Diagnostics 135
Print Quality Description 136
FEED and PAUSE Self Test 137
RIBBON (2). If 139
MEDIA (3) for the media 139
Specifications 141
General Specifications 142
Printing Specifications 143
Media Specifications 145
Ribbon Specifications 146
Printer Options 147
6/6/08 Z Series 149
Cutter Jam message, 118 150
HEAD COLD message 151
HEAD ELEMENT BAD message, 116 151
HEAD TOO HOT message, 117 151
INVALID HEAD message, 115 151
OUT OF MEMORY message, 118 152
PAPER OUT message, 116 152
RIBBON IN message, 116 153
RIBBON OUT message, 115 153
THERMISTOR FAULT message 154

Comentários a estes Manuais

Sem comentários

Zebra RZ400 Guia do Utilizador Página 132

Comentários a estes Manuais

Manuais e produtos relacionados com Digitalizar e Imprimir Zebra RZ400