Zebra ZE500 Guia do Utilizador Página 60
- Página / 170
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Printer Setup and Operation
Connect the Print Engine to a Power Source
60
P1051584-002 8/23/12
3. Turn on (I) the print engine.
The print engine boots up and performs a self-test.
Power Cord Specifications
Depending on how your print engine was ordered, a power cord may or may not be included.
If one is not included or if the one included is not suitable for your requirements, see
Figure 9
and refer to the following guidelines:
• The overall cord length must be less than 9.8 ft. (3 m).
• The cord must be rated for a minimum of 10 A, 250 V.
• The chassis ground (earth) must be connected to ensure safety and reduce electromagnetic
interference.
Caution • For personnel and equipment safety, always use an approved three-conductor
power cord specific to the region or country intended for installation. This cord must use an
IEC 320 female connector and the appropriate region-specific, three-conductor grounded
plug configuration.
- User Guide 1
- DECLARATION OF CONFORMITY 3
- Compliance Information 4
- Contents 5
- About This Document 9
- Who Should Use This Document 10
- Contacts 11
- Document Conventions 12
- Introduction 13
- Print Engine Orientation 14
- Print Engine Components 15
- POWER PAUSE STATUS DATA 16
- Default Password Value 20
- Control Panel Display 21
- • the non-resettable counter 26
- 3. Do you want to continue? 28
- PERMANENT 36
- Types of Media 39
- Printer Setup and Operation 40
- Ribbon Overview 41
- Adhesive Test 42
- Ribbon Scratch Test 42
- Printer Setup and 43
- Operation 43
- Handling the Print Engine 44
- Remove the metal spacer 46
- To Store the Print Engine 47
- To Ship the Print Engine 47
- Print Engine Installation 48
- 9.648 in 50
- (245 ± 0.1 mm) 50
- 0.445 in 50
- (11.3 mm) 50
- 16.62 in. (422.1 mm) 51
- Data Cables 58
- 115 V AC 59
- 230 V AC 59
- Power Cord Specifications 60
- Load Ribbon and Media 62
- Loading Media 65
- 19. Close the media door 69
- Printer Configuration 71
- Adjustment 71
- Changing Printer Settings 72
- Print Settings 73
- Applicator 75
- • ZE500-4 203 dpi: 832 dots 77
- • ZE500-4 300 dpi: 1228 dots 77
- • ZE500-6 203 dpi: 1344 dots 77
- • ZE500-6 300 dpi: 1984 dots 77
- ~JS when received 79
- • ENABLED 80
- • DISABLED 80
- Directory Listing 88
- Network Settings 89
- Print Server Settings > 92
- Print Server Settings 92
- Language Settings 93
- • ZPL II 94
- Sensor Settings 95
- Port Settings 96
- ZEBRA response messages are 98
- ZEBRA is selected, the print 98
- DSR/DTR for host 98
- LOAD BACKING 99
- P1051584-002 8/23/12 100
- REMOVE RIBBON 101
- CALIBRATING 101
- PLEASE WAIT 101
- RELOAD ALL 101
- Close the media door 102
- Remove Used Ribbon 103
- Adjust the Sensors 104
- Reflective Media Sensor 105
- Ribbon Sensor 105
- Toggle Positioning 106
- I) the printer.) 107
- Printhead Pressure Adjustment 108
- Routine Maintenance 111
- CLEAN HEAD NOW appears 112
- Clean the Media Compartment 113
- 7. Close the media door 114
- Lubrication 115
- Troubleshooting 117
- Printing Issues 118
- Ribbon Problems 121
- Error Messages 122
- 1) is likely 123
- O) the print engine 124
- I) the print engine 124
- Display/ 126
- Print Engine Condition 126
- Communications Problems 127
- Miscellaneous Issues 128
- Print Engine Diagnostics 130
- CANCEL Self Test 131
- PAUSE Self Test 132
- FEED Self Test 133
- Print Quality Description 134
- FEED + PAUSE Self Test 136
- CANCEL + PAUSE Self Test 136
- FE indicates a framing error 137
- PE indicates a parity error 137
- NE indicates noise 137
- Sensor Profile 138
- MEDIA (3) for the media 139
- Specifications 141
- General Specifications 142
- Printing Specifications 143
- Ribbon Specifications 143
- Media Specifications 144
- Applicator Interface Board 145
- Reconfiguration 145
- Remove Power and Data Cables 146
- ) off of the print engine 147
- 8/23/12 P1051584-002 149
- The installation is complete 155
- Glossary 157
- 8/23/12 P1051584-002 161
Manuais e produtos relacionados com Digitalizar e Imprimir Zebra ZE500
Digitalizar e Imprimir Zebra GX420t Guia do Utilizador
(108 páginas)
(108 páginas)
Digitalizar e Imprimir Zebra EPL2 Especificações
(138 páginas)
(138 páginas)
Digitalizar e Imprimir Zebra KR203 Especificações
(36 páginas)
(36 páginas)
(76 páginas)
(64 páginas)
Digitalizar e Imprimir Zebra 170PAX4 Guia do Utilizador
(164 páginas)
(164 páginas)
Digitalizar e Imprimir Zebra Z6Mplus Guia do Utilizador
(142 páginas)
(142 páginas)
(27 páginas)
Digitalizar e Imprimir Zebra 110PAX4 Guia do Utilizador
(164 páginas)
(164 páginas)
Digitalizar e Imprimir Zebra TTPM3 Especificações
(112 páginas)
(112 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais