Zebra Z6Mplus Guia do Utilizador descarregar pdf (Página 16)

Introduction

External View

13163L-001 Rev. A Z4Mplus/Z6Mplus User Guide 1/18/06

External View

Figure 2 shows the outside of the printer.

Figure 2 • External View

Electronics cover

Control panel

Media door

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 165 166

Z4Mplus/Z6Mplus 1
User Guide 1
Declaration of Conformity 3
Compliance Information 4
Contents 5
Who Should Use This Document 10
Contacts 11
Document Conventions 12
FEED button 13
CANCEL button 13
About This Document 14
Introduction 15
External View 16
Control Panel 17
Control Panel Buttons 18
Control Panel Lights 19
Printer Media Compartment 20
Printer Setup 21
Before You Begin 22
Handling the Printer 23
Select a Site for the Printer 24
Power Cord Specifications 26
Connector Locations 27
Types of Connections 28
Data Cable Requirements 30
Types of Media 31
Ribbon Overview 33
Adhesive Test 34
Ribbon Scratch Test 34
Operations 35
Media Loading Overview 36
Insert Media into the Printer 37
Fanfold Media 38
Load Media in Tear-Off Mode 39
Slide out the media guide 40
PAUSE to enable printing 41
5. Slide out the media guide 43
Load Media in Cutter Mode 48
Close the printhead assembly 51
Load Media in Rewind Mode 52
To operate in... Then 55
Load Ribbon 61
Remove Used Ribbon 64
Calibrate the Printer 66
Position the Media Sensors 67
If you are using… Then… 68
Adjust the Reflective Sensor 69
Adjust Printhead Pressure 71
Inside Dial Outside Dial 72
Install Memory Card 73
Configuration 75
Setup Mode 76
Exit Setup Mode 77
Default Password Value 78
Print a Configuration Label 79
LIST NETWORK 80
Control Panel LCD Displays 81
PRINT SPEED 82
2 IPS + 82
TEAR OFF +000 82
SENSOR SELECT 84
-AUTO SELECT + 84
PRINT METHOD 84
-THERMAL-TRANS. + 84
PRINT WIDTH 85
- 104 0/8 MM + 85
MAXIMUM LENGTH 86
-39.0 IN 988 MM 86
To format a memory card: 89
To initialize Flash memory: 90
SENSOR PROFILE 91
PRINT 91
COMMUNICATIONS 96
- NORMAL MODE + 96
CONTROL PREFIX 96
- < >7EH + 96
FORMAT PREFIX 97
- <^>5EH + 97
DELIMITER CHAR 97
- <,>2CH + 97
ZPL MODE 98
- ZPL II + 98
MEDIA POWER UP 98
- CALIBRATION + 98
HEAD CLOSE 99
BACKFEED 99
- DEFAULT + 99
LABEL TOP +000 100
- + 100
LEFT POSITION 100
- ±0000 + 100
Parameter 101
To skip these parameters: 101
To change the value shown: 101
LANGUAGE 103
Print Server LCD Displays 104
ENCRYPTION MODE 107
ENCRYPT. INDEX 107
Routine Maintenance 109
Lubrication 110
Cleaning Procedures 110
Clean the Rewind Option 114
Clean the Peel-Off Assembly 115
Close the media door 117
Clean the Cutter Module 118
Replace the cutter shield 119
Fuse Replacement 120
Troubleshooting 121
Troubleshooting Checklists 122
LCD Error Messages 123
LCD Display/ 124
Printer Condition 124
Caution • Turn off (O) the 125
O) the printer 125
I) the printer 125
Print Quality Problems 126
Note • A vertical drift of 128
Calibration Problems 129
Communications Problems 130
SAVE CHANGES in the 131
Calibrate 132
Printer Diagnostics 133
CANCEL Self Test 134
PAUSE Self Test 135
FEED Self Test 136
Print Quality Description 138
FEED and PAUSE Self Test 140
Data Ports 141
Parallel Data Port 142
36-Pin Connectors 143
Serial Data Port 144
Pin Configuration 145
RS-232 Interface Connections 146
Modem Connection 147
Specifications 149
General Specifications 150
Agency Approvals 151
Printing Specifications 152
Media Specifications 153
Ribbon Specifications 155
Printer Options 156
ZPL II Features 157
Supported Bar Codes 157
Cutter Jam message, 117 160
HEAD COLD message, 117 160
HEAD TOO HOT message, 116 160
OUT OF MEMORY message, 117 162
PAPER OUT message, 116 162
RIBBON IN message, 116 163
RIBBON OUT message, 115 163

Comentários a estes Manuais

Sem comentários

Zebra Z6Mplus Guia do Utilizador Página 16

Comentários a estes Manuais

Manuais e produtos relacionados com Impressoras de rótulos Zebra Z6Mplus