Zebra RW SERIES Especificações Página 69
- Página / 114
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
• 2-69 • RMAN-RWS-001 rev. B • RW Series Repair Procedures
Replacement Kit RK17479-003- RW 220 Media Guide
Installation Instructions
This kit includes the parts and documentation necessary to install the RK17479-003
Media Guide Kit in the RW 220 model printer. Read these instructions thoroughly
before attempting to install this kit.
The operator must wear a properly grounded ESD strap to perform the following
repair procedure.
Reference Materials
UMAN-RWS RW Series Users’ Guide
Tools Required
#0 or #1 Phillips Head Screw Driver
Cautions
Caution•Thisinstallationmustbeperformedonlybyaqualiedservicetechnician.
Unless otherwise specied:
• Always turn the printer off
• Remove the battery before installing any Replacement Kits.
• Remove media before installing this Replacement Kit.
Removing the Media Assembly
1. Turn the printer off and remove the battery pack.
2. Remove the Upper Housing, referring to procedure for RK17479-009. Pivot the
Upper Housing away from the Printer. You may elect to disconnect the LCD
and Keypad ex circuits form the CPU Board for ease of handling the Printer.
3. Unplug the following cables from the CPU Board: J2 (Bar Sensor), J10 (Gap
Sensor). You may also elect to unplug the Motor Cable from J6, which is on
the underside of the CPU Board.
4 Remove the two screws securing the CPU Board to the Lower Housing.
5. Remove the (4) Screws holding the Printer Frame and Media Cover to the
Lower Housing. Retain the Screws
6 Tilt the Printer Frame towards the back of the unit. While it is not necessary,
you may elect to remove the Printer Frame and Media Cover assembly from the
Lower Housing.
7. Remove and retain the (2) Screws securing the Media Assembly to the Printer
Frame.
continued on next page
- RW Series 1
- RMAN-RWS-001 rev.B • -ii • 2
- Contents 3
- RMAN-RWS-001 rev.B • -iv • 4
- Description 5
- Operating Modes 5
- Printing Technology 5
- Communications 5
- User Guide 5
- Diagnostic Tools 9
- Diagnostic Label Printout 9
- Label Vista™ 9
- Factory Technical Support 9
- Printing a Diagnostic Label 10
- Creating a Configuration Label 10
- Sample Configuration Label 10
- Introduction to Label Vista™ 13
- Starting Label Vista 13
- Equipment Required 14
- Running The Software 14
- Tools and Supplies 15
- Handling 15
- Storage and Handling 15
- • 2-16 • 16
- Unplug the Bar 16
- Sense Cable 16
- Peel the old Bar Sense 17
- Cable away from the 17
- • 2-20 • 20
- into place as 20
- • 2-22 • 22
- Installing the Media Assembly 23
- CPU CONNECTIONS 24
- Removing the Printhead 26
- Installing the Printhead 27
- Removing the Motor 30
- • 2-32 • 32
- • 2-34 • 34
- • 2-36 • 36
- Unplug LCD and Keypad flex 36
- Separate the Assemblies 37
- • 2-38 • 38
- Remove and retain Card 38
- Reader Assembly and 38
- Keypad and Housing Assembly 40
- Remove the Card Reader 41
- Install the Card Reader 42
- Kit p/n Description 45
- RK17393-029 Radio 802.11g Kit 45
- Remove the Radio Assembly 46
- • 2-48 • 48
- Replace the Belt Clip 52
- Clip, D-Ring 53
- Removing the “D” Rings 54
- Installing the “D” Rings 54
- Remove the Connector Door 56
- Install the Connector Door 56
- • 2-60 • 60
- Install the Base Plate 62
- Finish the Installation 62
- Unplug the 63
- Bar Sense 63
- Cable from J2 63
- • 2-64 • 64
- 10. Calibrate the Sensors 66
- • 2-72 • 72
- Changing the Media Core Size 73
- • 2-74 • 74
- • 2-78 • 78
- • 2-84 • 84
- 802.11b Antenna PCB Assembly 87
- Bracket, Radio (Card version 87
- • 2-88 • 88
- Radio PCB Assembly 88
- • 2-92 • 92
- Install the Upper Housing 96
- Removing the Controller Board 98
- Controller Board 100
- Test the Printer 101
- IN THE USA IN EUROPE 103
- RW Series Accessories 104
- PCC Example 106
- RW 420 Accessory Kits 107
- RW 420 Replacement Kits 107
- REPLACEMENT 109
- AK17463-005 109
- ITEM PART # DESCRIPTION 110
- RW 220 Accessory Kits 111
- RW 220 Replacement Kits 112
- 12 3 5 8 113
Manuais e produtos relacionados com Digitalizar e Imprimir Zebra RW SERIES
(68 páginas)
Digitalizar e Imprimir Zebra 3742 Manual de Serviço
(56 páginas)
(56 páginas)
Digitalizar e Imprimir Zebra 10/100 Manual do Utilizador
(116 páginas)
(116 páginas)
Digitalizar e Imprimir Zebra EPL2 Especificações
(248 páginas)
(248 páginas)
(37 páginas)
Digitalizar e Imprimir Zebra TTP2130 Especificações
(138 páginas)
(138 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais